AMTECH ad with circuit graphics reads: Your Gerbers are costing you weeks. The data package—not the fab line—is the #1 cause of PCB delays. Here’s how to get it right the first time.

PCB Gerber & Fabrication Spec Best Practices: How to Build a Data Package That Doesn’t Slow You Down

Route card / Article / 6 stops / 4 min
DOCUMENTArticle
FOREngineers and buyers
AUTHORAmtech engineering
IN 30 SECONDS
  1. A small set of recurring Gerber mistakes causes a large share of fab delays.
  2. Send a complete, clearly named Gerber package with explicit fab notes.
  3. You cannot control fab queues, but you can control your data package.

If your PCB project is running behind schedule, it’s tempting to look at the obvious suspects — a backordered component, a busy fab queue, a complex stack-up. But more often than not, the delay didn’t start on the manufacturing floor. It started in the data package you sent.

Misnamed, incomplete, or ambiguous files are one of the leading causes of fabrication errors and delays. A fabricator can’t quote what it can’t read, and it can’t build what it has to guess at. The encouraging part is that, unlike component lead times, your data package is something you fully control.

This guide breaks down the three things that make or break a release: avoiding the common Gerber mistakes, assembling a complete file package, and writing an explicit fabrication specification.

AMTECH ad with circuit graphics reads: Your Gerbers are costing you weeks. The data package—not the fab line—is the #1 cause of PCB delays. Here’s how to get it right the first time.

Common Gerber mistakes to avoid

A small set of recurring problems accounts for a disproportionate share of fab delays. Watch for these before you export:

  • Missing board outline layer. Fab shops cannot quote or produce a board without it — this is the most common dead stop.
  • Solder mask clearance set to zero. This causes all pads to be covered by mask.
  • Drill file units mismatch. Metric versus imperial errors slip through easily. Verify your EDA export settings.
  • Aperture macros not included. Some older Gerber viewers and importers require explicit aperture definitions.
  • Silkscreen artwork crossing into pads. This causes inspection issues and can create shorts.
  • Multiple board outlines in separate files. Consolidate all outlines into a single layer.

The Gerber file package

Provide a complete, clearly labeled Gerber package. A consistent naming convention removes ambiguity with your fab partner and keeps your files from being misinterpreted.

Layer / FileStandard naming convention
Top Copper*.GTL or *_Top_Copper.gbr
Bottom Copper*.GBL or *_Bot_Copper.gbr
Inner Layers (L2, L3…)*_L2.gbr, *_L3.gbr (etc.)
Top Solder Mask*.GTS or *_Top_Mask.gbr
Bottom Solder Mask*.GBS or *_Bot_Mask.gbr
Top Silkscreen*.GTO or *_Top_Silk.gbr
Bottom Silkscreen*.GBO or *_Bot_Silk.gbr
Board Outline*.GKO or *_Outline.gbr
Drill File (PTH)*.DRL or *_Drill_PTH.xln
Drill File (NPTH)*_Drill_NPTH.xln (if applicable)
NC Drill / Excelloninclude tool size table in header
IPC-2581 or ODB++acceptable as a comprehensive single-file alternative

Best practice: Always include a README.txt or layer-mapping document in the Gerber ZIP that identifies each file and its purpose. This eliminates ambiguity with fab partners — and it takes about five minutes.

PCB fabrication specification

Provide explicit fab notes either in the Gerber package or as a separate fab drawing. Do not rely on fab-shop defaults — if you don’t state a parameter, someone else will choose it for you.

Specification itemGuidance / example
Layer CountSpecify total layer count (e.g., 4-layer)
MaterialFR-4 standard, FR-4 high-Tg (>170°C), Rogers, Polyimide, etc.
Board ThicknessSpecify in mm or inches (e.g., 1.6mm / 0.063″)
Finished Copper WeightOuter layers (e.g., 1oz); inner layers (e.g., 0.5oz)
Surface FinishHASL (lead-free), ENIG, OSP, Immersion Silver, ENEPIG
Solder Mask ColorGreen standard; specify if blue, black, red, etc.
Silkscreen ColorWhite standard; specify if yellow or black
Min Trace / Spacee.g., 4/4 mil (0.1/0.1mm)
Min Drill (PTH)e.g., 0.2mm finished hole
Via Fill / CapSpecify if vias need tenting, plugging, or cap plating
Controlled ImpedanceState layer, trace width, target ohms, tolerance (e.g., ±10%)
IPC ClassIPC-6012 Class 2 or Class 3
UL MarkingRequired or not — specify
RoHS ComplianceSpecify if required for your program

The takeaway

You can’t always control your component lead times or how busy a fab line is. You can control whether your data package answers every question before it’s asked. Clear file names, a README, and an explicit fabrication spec are the cheapest, fastest schedule insurance available to a hardware team.

A clean package is also what makes instant quoting possible. With RapidRFQ, you can upload your BOM, Gerbers, and CPL and get a PCB assembly quote in minutes — but that speed only works when the underlying data is unambiguous.

Ready to put it to the test? Get an instant quote with RapidRFQ, or explore the full PCB Gerber & Fabrication Spec Best Practices guide in the Amtech Resource Center.


Amtech is an electronics manufacturing services partner based in Troy, Michigan. 701 Minnesota Drive, Troy, MI 48083 · (248) 583-1801

Get pricing for your build

Why Amtech

  • About 15 years of vapor phase reflow.
  • Family-owned for about 30 years, in Troy, Michigan.
  • Certified to ISO 9001, ISO 13485 and IPC-A-610.